Least value of design strength of bolt in bearing, design strength of bolt in shear is known as

Minimum pitch of bolts shall not be less than

Distance from centre of bolt-hole to the nearest edge is known as

A member if a truss which is under compressive force is known as

The minimum elongation percentage on standard gauge of mild steel is

In RCC retaining wall extra bars provided to satisfy the bearing pressure are known as

Minimum size of longitudinal bars in a column shall be

The member subjected to torsion shall be designed for fictitious shear which is function of the actual shear and torsion

The strength of a compression member with helical reinforcement the strength of similar member with lateral ties is

The maximum spacing of shear reinforcement measured along the axis of the member should not exceed

In limit state of flexure the maximum strain in concrete at the outermost compression fiber in bending is taken as

The value of the strength of the material below which not more than 5 percent of the test results are expected to fall

The process of collecting information about an object or an area without being the direct contact

Point where alignment changes from curve to straight

Which method is used for balancing the traverse when angular and linear measurements are equally precise ?

In an open traverse the included angle at a station is 209°16'00", deflection angle at that point is

When the vertical circle of a theodolite is on the right side of the observer, the position is

A small pocket instrument used for measuring horizontal and vertical angle

It is a combination of an electronic theodolite and an electronic distance meter

An angle is measured two or more times by allowing the vernier to remain clamped each time at the end of each measurement instead of setting it back at zero when sighting at the previous station

It is the line passing through the intersection of the horizontal and vertical cross hairs and optical centre of the object glass and its continuation

Contour lines of different elevation can intersect only in the case of

It is the method of direct leveling the object of which is solely to determine the difference in two point regardless of the horizontal position of the point with respect of each other

The process of determining the plotted position of the station occupied by the plane table, by means of sight taken towards known point, location of which have been plotted

Convert the angle 327°24'00" to Quadrantal bearing

The meridian through a point is the line in which a plane, passing that point and the north and south poles, intersection with surface of the earth

The length of a surveyor's chain is

What is the minimum amount of DO required for the survival of aquatic animals?

The term is used to indicate the sludge which is obtained by settling sewage in presence of abundant oxygen

Amount of oxygen required to carrying out the biological composition of dissolved solids in sewage under aerobic condition at standard condition

The term used to indicate the waste water from bathroom, kitchen etc.

The valve is an automatic device which allows water to go one direction only

The theoretical time taken by a particle of water to pass between entry and exit of a setting tank is known as

For potable water, the amount of chloride should not exceed

It indicate the loss of water penetrated into the soil it may join some underground water

The portion from which the branches is removed receives nourishments from the trunk and dark rings which are known as

The process of heating the limestone to redness in contact with air is termed as

In chemical classification of rock, marble is known as

The property of increase in volume of fine aggregate due to moisture is called

A conic section which have only one directrix is

ക്ലോക്കിലെ സമയം 3 : 30 ആയാൽ സൂചികൾ തമ്മിലുള്ള കേ കോണളവ് എത്ര?

സുവർണ്ണ ചതുഷ്കോണ സൂപ്പർ ഹൈവേയുടെ ചുമതല നിർവ്വഹിക്കുന്നത് :

താഴെ കൊടുത്തിരിക്കുന്നവയിൽ പാരമ്പര്യേതര ഊർജ്ജസ്രോതസ്സ് ഏത്? :

സമയം 3 : 15 ആയിരിക്കുമ്പോൾ ക്ലോക്കിലെ മിനുട്ട് സൂചിയും മണിക്കൂർ സൂചിയ്ക്കും ഇടയിലുള്ള കോൺ എത്

തർക്കശാസ്ത്രത്തിന്റെ പിതാവ്

കേരള സംസ്ഥാനം നിലവിൽ വരുമ്പോൾ സംസ്ഥാനത്ത്എത്ര ജില്ലകളുണ്ടായിരുന്നു.

_____________ is the 25th meeting of the conference of parties (COP) to the United Nations Framework Convention on Climate Change (UNFCCC).

Rotterdam Convention came into force in _____

Rotterdam Convention was adopted in ______

_______is an international environmental convention on Prior Informed Consent (PIC) Procedure for Certain Hazardous Chemicals and Pesticides in International Trade.