Face left and face right observations eliminate the error

In the case of square method of contouring,the size of squares depends upon:

If RL of a BM is 100.00 M , back sight is 1.5 M and foresight is 2.5 M , RL of the forward station is

The process of determining the location of the instrument station by drawing rays from the locations of known station is called

Imaginary lines joining the points of equal declination on the surface of earth is called

Fore and back bearings of a line whose end stations are free from local attraction,should differ by

The method of stepping is used for measuring horizontal distance in the case of

A straight line joining a station on a main survey line and another station on another line is called

The stress induced in body in the case of a suddenly applied is ..............the stress induced, when the fame load is applied gradually

Moment of inertia of a rectangular section having breadth b and depth d is

A frame which is composed of the members just sufficient to keep the body in equilibrium, when loaded, without any change in its shape

The stress which is considered as the allowable stress for design purpose

The maximum strain energy that can be stored in an elastic member without exceeding its elastic limit

The thermal strain of a bar of length L is heated at T0 C and having a coefficient of expansion and E Young's modulus

The ratio of ultimate stress to working stress is

When a body is subjected to shear stress the modulus of rigidity is :

Poisson's ratio

Property of materials of returning to their original position after removing the external force

The ratio of the limiting friction to the normal reaction between the two bodies is known as

The distance from an axis of reference where the mass or area of body is assumed to be concentrated is called

Two forces P= 3 N and Q = 4 N act on particle and their lines of action are inclined to each other at an angle of 90 degree. What is the third force R will keep the particle in equilibrium

The unit of acceleration

When all the forces acting on a body, lies in the same plane, they are called

Effective length of compression member when effectively held in position and restrain against rotation at both ends

The maximum slenderness ratio for a member carrying compressive force due to dead load should not exceed :A.

It is assumed that the bending moment at any section of the plate girder is resisted by the

The angle connect the web and the flange plates

The length of sides of the largest right angled in the cross section of the fillet weld is designated as the

The centre to centre distance of rivets of adjacent rows measured in the direction of stress is

The permissible stress in axial tension on the net effective area of the steel section shall not exceed

In the limit state of collapse, the maximum strain in the concrete at the outermost compression fiber is taken as

When the ratio of long span to short span is less than two, the slab is designed as

The spacing of longitudinal bars measured along the periphery of the column shall not exceed

The basic value of span to effective depth ratio for span upto 10 m for simply supported beam

The minimum area of tension reinforcement shall not less than that given by the following

Compression in bars in a beam or slab when the compressive resistance of the concrete in taken into account, the modular ratio should be multiplied by

The permissible tensile stress of High Yield Strength Deformed bar conforming to IS1139 in N/mm²

The section in which the stresses in concrete and steel are simultaneously reach the allowable value, then the section is

The distance between the line of action of the resultant compression and the line of action of resultant tension is known as

The permissible stress of M 20 concrete in compression in N/mm² is

The initial lead and lift of earth work excavation in ordinary soil and depositing on bank is

The standard stacks for broken stone unless otherwise specified, the length of stack shall be of

In Auto Cad there are...........options to draw an arc

In Auto CAD the function of the key F8 is

According to the method storage, which one of the following is not identical with the others

Which one of the following is a chemically treated reprographic method

The process which specifies what the right and left hands of the worker was doing is known

The fastening pipe thread designated by size G 1/2 have a thread pitch of

With worn gear the possible speed reduction

Pick the odd one out: