'Naothanathinte Surya Thejas' is the biography of

Minimum width of tread without nosing in residential building is

Minimum area of bathroom with water closet

Set back distance required at rear of a building is

The drafting setting used to on strain the movement of cursor either horizontal or vertical direction is

The capacity of doing work by an artisan or skilled labour in the form of quantity of work per day is known as

The value at the end of the utility period without being dismantled

The term used to denote the gradual reduction in the useful life of the asset is

The total area of floor in between walls and consists of floor of all rooms, verandahs, passages, corridors etc. are known as

The formal approval by the department concerned of the project proposal for incurring the expenditure on a work initiated is

The supports provided to the super structure of the bridge at the abutments and piers allowing free longitudinal or angular movements to the main girders or trusses of bridge

Upstream nose of a bridge pier shaped for easy and smooth flow of water through it is known as

Paved surface used for landing and take-off of aircraft is known as

Station which are meant only for the control of the track is called

Arrangement to divert train from one track to another is known as

The pavement which can resist tensile stresses and having very little resistance to deformation under the wheel load

It is a safety island and serves the dual purpose of affording the protection to the pedestrians and segregating the traffic into the proper channel

The solution of bitumen, asphalt or coal tar in solvents is

It is defined as the slope of the line joining the crown and the edge of the surface

Canal normally used for diversion or flood water of river is

The area of the land which drain into the stream of reservoir is called

The amount of water stored in river channel without any artificial storage is known as the

The relation between the area irrigated and the quantity of water used is expressed as

The crops which cannot normally be grown without irrigation water are called

An embankment protected on all sides by stone or concrete block, built at right angle to the axis of the weir separation of the weir and the under sluices

It is the overflow portion of dam, over which surplus discharge flow from the reservoir to the down stream

The permeable formation having structure which permits appreciable quantity of water to move through them under ordinary field condition

I is the ratio of inertia force to the gravity force

It is a tank is also provided just on the upstream of the power to control the pressure variation and eliminate the effect of water hammer

It is a velocity at which the flow changes laminar flow to the turbulent flow

It is an instrument to determine the velocity at required point in the flowing stream

When a body is fully immersed in water, the point through which the resultant pressure act is known as

The tendency of a material to fracture without appreciable deformation is called

A fixed beam of span 'L' is loaded with central point load 'W'. The BM at centre will be

A circular column of diameter 'd' under any load will have compressive stress throughout the section of the load act within concentric circle known as core, of diameter

Modulus of section 'z' of hollow circular section with external diameter 'D' and internal diameter 'd' will be

The shear stress in a circular shaft of radius 'r' subjected to torsion, is maximum at a point

A simply supported beam of span 'l' carries a uniformly distributed load 'w' per unit length, the maximum BM at the midpoint will be

The maximum energy stored at elastic limit of a material is known as

The ratio of lateral strain to axial strain is a constant for a homogeneous material

The member of a roof truss subjected to transverse load and rest on rafters are known as

Least value of design strength of bolt in bearing, design strength of bolt in shear is known as

Minimum pitch of bolts shall not be less than

Distance from centre of bolt-hole to the nearest edge is known as

A member if a truss which is under compressive force is known as

The minimum elongation percentage on standard gauge of mild steel is

In RCC retaining wall extra bars provided to satisfy the bearing pressure are known as

Minimum size of longitudinal bars in a column shall be

The member subjected to torsion shall be designed for fictitious shear which is function of the actual shear and torsion

The maximum spacing of shear reinforcement measured along the axis of the member should not exceed