The method of stepping is used for measuring horizontal distance in the case of

Fore and back bearings of a line whose end stations are free from local attraction,should differ by

Imaginary lines joining the points of equal declination on the surface of earth is called

The process of determining the location of the instrument station by drawing rays from the locations of known station is called

If RL of a BM is 100.00 M , back sight is 1.5 M and foresight is 2.5 M , RL of the forward station is

In the case of square method of contouring,the size of squares depends upon:

Face left and face right observations eliminate the error

The straight lines between two consecutive traverse stations are called

The latitude and departure of any station with respect to the preceding stations known as

The method employed when linear and angular measurements of the traverse are of equal accuracy

The leveling used to determine the difference of elevation between two points which are quite apart and when it is not possible to set up the leveling instrument midway between the points

The instrument used for reproducing,enlarging or reducing the map

If the values of elevation go on increasing towards the centre of a series of closed contour lines on the plan of the map indicate

A line joining the optical centre of the object glass to the centre of the eye pieceof a level is

The ratio of equivalent length of column to the minimum radius of of gyration is called

The ratio of equivalent length of column having one end fixed and other end hinged,to its length isA.1/2B.1/2C. 82D.

Which type of loading produces direct and bending stresses

If the maximum available frictional resistance is greater than the horizontal water pressure the dam should be safe against

The pressure exerted by the retained earth on the retaining wall is called

The maximum bending moment of a cantilever of length L carrying UDL W/m, in the entire length

The shape of bending moment diagram of a simply supported beam carrying point load at the centre is

The point of inflexion occur in the

In the case of circular section of diameter d, the section modulus is given by

The maximum bending stress of a beam will be at the

A square section with side b of a beam is subjected a shear force of F, the magnitude of shear stress at the top edge the square is

A cantilever length L is carrying a uniformly distributed load of w per unit run for a distance a from fixed end. The slope at free end is given by

A simply supported beam of length L carrying point load W at the mid point. What is the deflection at the centre of beam

A fixed beam of length L carrying a point loud W at the centre. The fixing moment at the end is

A propped cantilever of length 4 m carrying a udl of 2 KN/m for the entire length and propped at the end. The prop reaction will be

The support moments of the continuous beam can be determined by applying of:

The ratio of moment produced at a joint to the moment applied at the other end;without displacing it is called

In the case of fixed beam, the maximum bending moment can be reduced by

In the case of fixed beam carrying eccentric Load, the shape of BM diagram due to fixing moment will be

A continues beam 12 m long supported Over two span 6 m each carries a concentrated 40 KN each at the centre of each span. The bending moment at the support is.

The rock formed by the deposition of product of wreathing on the pre existing rocks

The process of grinding clay with water and making it plastic is known as

The lime which are obtained by the calcinations of comparatively pure lime stone is known as

The instrument used to determine the consistency of cement

The cracks which partly or completely separate the fibers of wood

A solid substance in a fine state of division and forms the bulk of paint:

The size of concrete cube used to determine the compressive strength of concreteB.

A groove provided on the underside of sill,cornice and coping so that the rain water can be discharged:

A brick lald with its length parallel to the face or direction of wall

In which bond the face elevation is of English bond and the filling as well as backing are on Flemish bond

The wedge shaped units forming the courses of an arch

The vertical member which is employed to sub divides a window or door vertically

The wooden pieces which are placed horizontally on principal rafters to carry common rafters are

The horizontal platform between two flights of a stair is known as

A board concrete pile having one or more bulbs in its lower portion is called

The method in which the approximate cost of a project is arrived based on its service unit method